○ FullHD ○ Wifi & GPS ○ 1,5 inch LCD scherm ○ 512gb support Read more
€99,00
○ FullHD ○ Wifi & GPS ○ 1,5 inch LCD scherm ○ 512gb support
This Vantrue Element 1 Lite (E1 Lite) is Vantrue's entry-level dashcam. This super-small dashcam fits in any car and is barely noticeable due to its design. It films FullHD video and is equipped with Wifi, GPS and an extended parking mode (when connected with the optional hardwire kit).
This Vantrue E1 Lite records in quite sharp FullHD 1920*1080p footage in 30fps. With HDR (High Dynamic Range), the contrast of the recordings is very good and the surroundings are recognisable even in the dark.
The Vantrue E1 Lite is equipped with a small 1.5-inch LCD screen on which the recordings are visible and you can easily operate the menu. The screen has a screensaver that activates after 1 minute so it doesn't bother you while driving. You can also turn the screen on and off with the voice command ‘Turn on screen’ and ‘Turn off screen’.
Within range of the dashcam (+/- 5 metres), you can easily view the recorded videos on your smartphone via the Vantrue App for iOS or Android. The videos can be viewed live and you can download saved videos to your phone so you can share them directly. The menu is also easy to operate via the App to change settings very quickly.
The Vantrue E1 Lite is equipped with GPS so that current speed and coordinates are tracked. The speed can be displayed at the bottom of each video if desired, and the film location and route can be viewed later via the App.
The Vantrue E1 Lite allows you to control the dashcam via (English) voice commands. Commands like ‘Make picture’, ‘Turn off screen’, ‘Turn on audio’ and ‘Lock the video’ allow you to use the dashcam safely while driving and not miss a single incident.
Vantrue offers the ability to secure your car while parking. Connect your Vantrue dashcam with the OBD or 3-wire hardwire kit to power the dashcam even when the car is switched off. The power supply transmits a signal to the dashcam as soon as you turn off the car so that parking mode is automatically enabled.
Parking mode works only in combination with the OBD or 3-wire hardwire kit. In this power supply there is a safety device that cuts the power at a certain voltage so you don't end up with a dead battery.
Vantrue has four recording modes during parking:
Motion detection: Motion detection (with adjustable sensitivity) where the dashcam is on standby until a visual movement is detected in the image. After this, it records 5 seconds before and 30 seconds after the incident.
Collision detection: Vibration detection (with adjustable sensitivity) where the dashcam switches off until a vibration is detected. It then turns on, records for 1 minute and turns off.
Low bitrate recording: Continuous recording in lower quality (720p or 1080p in 15fps) to save space on the SD card. As soon as a vibration is detected, normal 1-minute recording is started.
Time lapse recording: Continuous recording in 1fps, 5fps, 10fps or 15fps to save space on the SD card. At 1fps, a 30-minute period is played back in 1 minute. As soon as a vibration is detected, a normal 1-minute recording is started.
The Vantrue E1 Lite has a wide viewing angle of 160 degrees to capture a very large area around the car.
The Vantrue E1 Lite attaches to the windscreen with a handy self-adhesive GPS holder with magnetic connection. The dashcam can be clicked in and out of this holder in one move. To use your Vantrue E1 Lite in multiple cars, an additional GPS holder is available (see accessories).
Attach the optional CPL (Polaroid) filter to your Vantrue dashcam to counteract annoying reflections from the dashboard or interior. The filter fits onto the dashcam in no time and is easily adjusted by turning it.
The Vantrue E1 Lite has a built-in G-sensor. This sensor records vibrations in case of a collision. The current video is stored securely in that case.
The Vantrue E1 Lite is equipped with loop recording that automatically overwrites the oldest images with new ones. Videos are stored in shorter fragments of 5 minutes and once the SD card is full, the oldest fragment is deleted.
Secure recordings (manually selected or detected by the G-sensor) are stored in a separate folder and are not deleted by loop recording. This way, you always have access to the latest and most important videos.
The Vantrue E1 Lite attaches to the windscreen with a handy self-adhesive GPS holder with magnetic connection. The dashcam can be clicked in and out of this holder in one move. To use your Vantrue E1 Lite in multiple cars, an additional GPS holder is available (see accessories).
Vantrue is one of the few dashcam brands with support for SD cards up to 512gb. With 512gb, you can store up to 108 hours (over 4 days) of FullHD videos.
| General | |
|---|---|
 Brand |
Vantrue
|
 Price |
€99,00
|
 Review |
|
 Warranty |
|
 EAN barcode |
5904209821235
|
| Image | |
 ChannelsThe number of cameras or “channels” the dashcam uses to film. A 1-channel 1CH dashcam films only the front and a 2CH also has a rear camera. A 3CH has an additional interior camera and a 4CH dashcam often consists of four separate cameras.
|
1CH
|
 ResolutionVideo resolution indicates how many pixels the videos consist of. Therefore, the higher the resolution, the larger the videos are and the more details can be seen. For example, 4K refers to the number of horizontal pixels (3840) of the video.
|
FullHD
|
 Night visionThe quality of video at night or in low light conditions is mainly determined by the image sensor used in the dashcam. Some dashcams also have infrared LEDs, but these are mainly effective at short distances for interior cameras, for example.
|
|
 Viewing angleDashcams always have a round “fish eye” lens with a wide viewing angle so that a larger area around the camera is recorded. So a wider viewing angle means you capture more but also results in some distortion at the sides.
|
|
 Image sensorThe image sensor used determines the resolution of the videos and is the biggest determinant of dashcam image quality.
|
|
 ProcessorThe chip or processor is basically the computer or brain of the dashcam. It converts the images into digital video files (usually MP4 or AVI). Along with the image sensor, it is a major determinant of the quality of the final videos.
|
|
| Functions | |
 WifiWifi allows you to view images on your phone or tablet within range of the camera (5 to 10 meters) without having to remove the SD card from the dashcam.
|
|
 GPSA dashcam with GPS records the current speed and location while filming. The speed can be displayed at the bottom of each video, this can be useful in determining the question of fault in an accident.
|
|
 Parking modeA dashcam with parking mode secures your car when it is parked. To use parking mode, the dashcam must be connected with a permanent power cable at the car's fuse box or to a Powerbank (see accessories).
|
|
 Parking mode typesIn parking mode, a dashcam films in a way that consumes less data and power such as in Time lapse (1 picture per second), motion detection or vibration detection. The dashcam automatically switches to this mode when you turn off the car's ignition.
|
Trillingsdetectie, Bewegingsdetectie, and Time lapse
|
 CloudA dashcam with Cloud allows you to watch live and receive notifications of (parking) events anywhere in the world. To use Cloud, you need a SIM card with internet connection and sometimes a (paid) user account.
|
|
 Loop recordingLoop recording allows the dashcam to keep recording continuously with a full SD card. When the SD card is full it automatically overwrites the oldest videos so that always the last trips are stored on the SD card.
|
|
 G-sensorThe G-sensor in a dashcam records vibrations and therefore notices when a collision or incident occurs. In that case, the current recording is stored separately and securely so that it cannot be overwritten by the Loop recording.
|
|
 ADASAdvanced Driver Assistant System that can warn of dangerous situations such as a rapidly approaching predecessor or undetected lane changes. Be aware that this system is never 100% reliable and due to limited input is not always effective.
|
|
| Device | |
 LCD displayAn LCD screen makes it easy to adjust the dashcam, operate the menu and view live and saved videos. With most dashcams, the LCD screen turns off after a few minutes of driving so it is not distracting to the driver.
|
|
 LCD size |
|
 TouchscreenA dashcam with touchscreen LCD screen you operate by using your fingers on the screen like on your smartphone. A dashcam without a touchscreen is operated with buttons.
|
|
 Mount typeA dashcam is mounted on the windshield with a suction cup or adhesive mount. Suction cup mounts are easier to remove but slightly less durable, while adhesive mounts are sturdier and more durable but more difficult to remove.
|
Zelfklevend
|
 Plug typeThe type of plug used to power the dashcam. Can be useful if you want to switch to another model of dashcam without having to reinstall the entire power supply.
|
|
 CPL filter optionA CPL filter acts like Polaroid sunglasses in front of the lens and can prevent harmful or annoying reflections. Keep in mind that it is better to remove the CPL filter at night because otherwise the videos may become too dark.
|
|
 Memory typeThe way videos are stored in the dashcam. Most dashcams use a Micro SD card, others have built-in eMMC memory. Preferably use a new and fast SD card from a well-known brand to avoid failures.
|
|
 SD supportWith a Micro SD card, the storage capacity - depending on the dashcam model - can be expanded to 128gb, 256gb or even 512gb. Up to about 24 hours of FullHD or 12 hours of 4K video can be stored on a 128gb SD card.
|
32gb, 64gb, 128gb, 256gb, and 512gb
|
 MicrophoneA microphone also records sound with the videos. Most dash cams allow you to turn off the microphone with the push of a button.
|
|
 BatteryA dashcam is equipped with a Li-ion battery or capacitor (Super capacitor). The batteries are very small and only intended to be able to turn off the dashcam if the power fails. Therefore, a dashcam must always be connected to the power supply.
|
|
 PowerThe voltage at which the dashcam can be used. Most dashcams are compatible with all cars and trucks with 12V and 24V. Always use the original included power supply or optional hardwire kit.
|
12V and 24V
|
 Weight |
389 g
|
 Dimensions |
|
| Contents | |
 In the box |
|
 | |
|---|---|
| General | |
| Brand |
Vantrue
|
| Price |
€99,00
|
| Review |
|
| Image | |
| Channels The number of cameras or “channels” the dashcam uses to film. A 1-channel 1CH dashcam films only the front and a 2CH also has a rear camera. A 3CH has an additional interior camera and a 4CH dashcam often consists of four separate cameras.
|
1CH
|
| Resolution Video resolution indicates how many pixels the videos consist of. Therefore, the higher the resolution, the larger the videos are and the more details can be seen. For example, 4K refers to the number of horizontal pixels (3840) of the video.
|
FullHD
|
| Night vision The quality of video at night or in low light conditions is mainly determined by the image sensor used in the dashcam. Some dashcams also have infrared LEDs, but these are mainly effective at short distances for interior cameras, for example.
|
|
| Viewing angle Dashcams always have a round “fish eye” lens with a wide viewing angle so that a larger area around the camera is recorded. So a wider viewing angle means you capture more but also results in some distortion at the sides.
|
|
| Image sensor The image sensor used determines the resolution of the videos and is the biggest determinant of dashcam image quality.
|
|
| Processor The chip or processor is basically the computer or brain of the dashcam. It converts the images into digital video files (usually MP4 or AVI). Along with the image sensor, it is a major determinant of the quality of the final videos.
|
|
| Functions | |
| Wifi Wifi allows you to view images on your phone or tablet within range of the camera (5 to 10 meters) without having to remove the SD card from the dashcam.
|
|
| GPS A dashcam with GPS records the current speed and location while filming. The speed can be displayed at the bottom of each video, this can be useful in determining the question of fault in an accident.
|
|
| Parking mode A dashcam with parking mode secures your car when it is parked. To use parking mode, the dashcam must be connected with a permanent power cable at the car's fuse box or to a Powerbank (see accessories).
|
|
| Parking mode types In parking mode, a dashcam films in a way that consumes less data and power such as in Time lapse (1 picture per second), motion detection or vibration detection. The dashcam automatically switches to this mode when you turn off the car's ignition.
|
Trillingsdetectie, Bewegingsdetectie, and Time lapse
|
| Cloud A dashcam with Cloud allows you to watch live and receive notifications of (parking) events anywhere in the world. To use Cloud, you need a SIM card with internet connection and sometimes a (paid) user account.
|
|
| Loop recording Loop recording allows the dashcam to keep recording continuously with a full SD card. When the SD card is full it automatically overwrites the oldest videos so that always the last trips are stored on the SD card.
|
|
| G-sensor The G-sensor in a dashcam records vibrations and therefore notices when a collision or incident occurs. In that case, the current recording is stored separately and securely so that it cannot be overwritten by the Loop recording.
|
|
| ADAS Advanced Driver Assistant System that can warn of dangerous situations such as a rapidly approaching predecessor or undetected lane changes. Be aware that this system is never 100% reliable and due to limited input is not always effective.
|
|
| Device | |
| LCD display An LCD screen makes it easy to adjust the dashcam, operate the menu and view live and saved videos. With most dashcams, the LCD screen turns off after a few minutes of driving so it is not distracting to the driver.
|
|
| LCD size |
|
| Touchscreen A dashcam with touchscreen LCD screen you operate by using your fingers on the screen like on your smartphone. A dashcam without a touchscreen is operated with buttons.
|
|
| Mount type A dashcam is mounted on the windshield with a suction cup or adhesive mount. Suction cup mounts are easier to remove but slightly less durable, while adhesive mounts are sturdier and more durable but more difficult to remove.
|
Zelfklevend
|
| Plug type The type of plug used to power the dashcam. Can be useful if you want to switch to another model of dashcam without having to reinstall the entire power supply.
|
|
| CPL filter option A CPL filter acts like Polaroid sunglasses in front of the lens and can prevent harmful or annoying reflections. Keep in mind that it is better to remove the CPL filter at night because otherwise the videos may become too dark.
|
|
| Memory type The way videos are stored in the dashcam. Most dashcams use a Micro SD card, others have built-in eMMC memory. Preferably use a new and fast SD card from a well-known brand to avoid failures.
|
|
| SD support With a Micro SD card, the storage capacity - depending on the dashcam model - can be expanded to 128gb, 256gb or even 512gb. Up to about 24 hours of FullHD or 12 hours of 4K video can be stored on a 128gb SD card.
|
32gb, 64gb, 128gb, 256gb, and 512gb
|
| Microphone A microphone also records sound with the videos. Most dash cams allow you to turn off the microphone with the push of a button.
|
|
| Battery A dashcam is equipped with a Li-ion battery or capacitor (Super capacitor). The batteries are very small and only intended to be able to turn off the dashcam if the power fails. Therefore, a dashcam must always be connected to the power supply.
|
|
| Power The voltage at which the dashcam can be used. Most dashcams are compatible with all cars and trucks with 12V and 24V. Always use the original included power supply or optional hardwire kit.
|
12V and 24V
|
| Weight |
389 g
|
| Dimensions |
|
| Contents | |
| In the box |
|
